Re-Post the DD mounting options

[kevin]

Before the old site crashed there were some interesting pictures of mounting ideas you guys had. The best looking option was the modified Edge mount with the DD inside.
Any one have any new ideas with pictures of mounting locations?

I hate having the DD in my windshiled for fear someone will break in to steal it thinking it is a GPS.

[mick1955]

There have been I believe 4-5 stolen so far. There is no way I would leave mine in the truck. This vehicle is just too easy for thief's to get into. Check out some of the other forums and you'll see what I'm talking about. I mount mine in the windshield, but also don't like it there. Gets too hot with this Texas heat. I have mounted it in the cup holder on the lower part of the dash, but that is just too low to see. I'm in the process of trying to mount mine in front of the tach. Don't really use it that much anyway. Just not too sure if there is enough room, guess I'll find out soon. Some have removed the upfitter switches and installed it there. Good luck.

[Kimminau2]

I went with the Edge pod. It looks great and is incredibly easy to use. Mine snaps into place nice and tight, does not need any tape or velcro to hold it in. the DD covers the edge hole completely. It is in a great spot and is easy to see and use.

[eric.davis]

post up some pictures of your DD installed so I have some ideas as to where I would like to mount it if these tunes cover what is on my truck

[Blaster7Romeo]

Yea any pics would be grate. I kind of like the simple way the edge can be just slid under the dash.. I just dont like the suction cup idea

[kevin]

Originally Posted by Kimminau2

I went with the Edge pod. It looks great and is incredibly easy to use. Mine snaps into place nice and tight, does not need any tape or velcro to hold it in. the DD covers the edge hole completely. It is in a great spot and is easy to see and use.

Did you modify the opening to fit the DD unit or does it sit on the surface of the mount?
Any pics?

[Kimminau2]

Originally Posted by kevin

Did you modify the opening to fit the DD unit or does it sit on the surface of the mount?
Any pics?

It sits on the surface of the pod, right over the hole for the edge. Someone else posted this method earlier and I did the same thing. I just got a short piece of flat metal, drilled a couple of holes in it to screw to the DD (using the DD mounting holes) put the plate inside the edge pod and mounted the DD. It just clamps in place. Real easy.

I will try to get some pics of it today.

[08Fuston]

Here's a few pics of mine. Helps keep it out of the sun, out of sight for the most part, and keeps the honest people honest.

[kevin]

Originally Posted by Kimminau2

It sits on the surface of the pod, right over the hole for the edge. Someone else posted this method earlier and I did the same thing. I just got a short piece of flat metal, drilled a couple of holes in it to screw to the DD (using the DD mounting holes) put the plate inside the edge pod and mounted the DD. It just clamps in place. Real easy.

I will try to get some pics of it today.

Is there a possibility to enlarge the opening so the DD sits more inside the pod? Please post a picture if possible of your setup.

Thanks

[kevin]

Originally Posted by 08Fuston

Here's a few pics of mine. Helps keep it out of the sun, out of sight for the most part, and keeps the honest people honest.

This looks interesting. Can you explain how you mounted this so it stays in place?

[eric.davis]

yes please and how you went to fabricating and installing it in that location because i too dont like having my current setup (livewire) mounted on my window just an obstruction to me while im driving. so any installation pics or if you can remove it and re-install it for us i think we would all owe you a beer

[08Fuston]

Ok, you guys asked for it, and it is really rather simple. I took the mounting bracket that came with the DD, and took it apart. The only parts of it that I am using are the plate that screws to the back of the DD, and the arm that comes off of the to the hinged section. Leave the screw in it, back the nut off just enough to expose the threads on the screw. I used a small dab of blue loctite on mine to keep the nut on. I then held the entire assembly in place, then took a long industrial Ty-Wrap, routed it around the screw, then around the steel dash support structure behind where the ashtray used to be. Then I carefully routed the cable over to my OBDII port. It was really quite simple. I am sure someone out there can find a better way to do this, but you have to realize, that mine has been installed this way since the first day I got it, and it hasn't budged.

P.S. I am always ready for a cold one

[Graygh0st]

Here are the pictures I originally posted on using a Edge mount with the DashDaq. Make it look like a clean instal. Easy to see and out of the way of the window area.

[eric.davis]

Originally Posted by 08Fuston

Here's a few pics of mine. Helps keep it out of the sun, out of sight for the most part, and keeps the honest people honest.

how easy is it to monitor everything with the DD mounted down there? I like the fact that I'm able to just glance over and see all my temps, boost and fuel on the window just dont like having it on the window blocking my view.

Originally Posted by Graygh0st

Here are the pictures I originally posted on using a Edge mount with the DashDaq. Make it look like a clean instal. Easy to see and out of the way of the window area.

now I like this setup and how its out of the view of the window, but is it easily removable if you dont want it there when your not in the truck?

and for both of you. do you remove the unit when you leave your truck or just leave it mounted the entire time because I would think that fuston yours would be a better idea if you plan on leaving it mounted all the time. Just dont know if I like the fact you have to look down to monitor everything. Who knows I'll probably end up getting pillar gauges after I get back once I get my lift put on. Then I wont have a problem with worrying about the DD and where to mount it.

[Blaster7Romeo]

yea when i am going about 80 or 90 i don't like the idea of taking my eyes off the road to look down to see what my EGT's are

[08Fuston]

I mounted mine where I did for the reason that I feel like it is relatively safe from prying eyes, and out of the sun. Yes, I leave it in the truck. As far as being able to see it easily, yes, it is just a quick galnce. I have only four gauges set up. Looks like squares in each corner with numbers big enough to read from the back seat. I monitor trans fluid temp, egts, engine coolant temp, and engine oil temp.

[eric.davis]

I just ordered mine today. Matt is loading up the DD tonight with the 75, 150, 210 and 250. The 6 things that I monitor on my livewire currently are Engine Oil Temp, Engine Coolant Temp, Trans Temp, Boost and Fuel Pressure. Those are what I'm concerned about. I love the look of how its mounted there and I even mock placed my livewire there and I like the look of it and probably will end up mounting it there this weekend when I get the time and figure out how to monitor all of those things. I cant wait

[fryjr]

Graygh0st has the same mount I had. I loved it until it was stolen from my work's parking lot. We have security patrolling the parking lot and the thief broke my window to steal my DD in the Edge pod mount. That takes a whole 1 sec to rip out. Nobody reported seeing the theif. I will never leave my DD in my truck again. I will take it on trips but no daily driving.

[Glassman]

Still experimenting with mine.

[hotlicks2go]

http://i523.photobucket.com/albums/w...o/DSC05111.jpg

http://i523.photobucket.com/albums/w...o/DSC05114.jpg

[Gerry]

Originally Posted by hotlicks2go

http://i523.photobucket.com/albums/w...o/DSC05111.jpg

http://i523.photobucket.com/albums/w...o/DSC05114.jpg

Where did you get that mount from and can you quickly remove the DD when you park the truck?? It looks like you can but I can't tell for sure.

Thanks,
Gerry

[mick1955]

hotlicks2go I too want to know where you got the mount from. Looks great by the way!!

[hotlicks2go]

That mount is for a Sirius satalite radio. From a car kit. They all have the same mounting hole pattern as the DashDaq. Works real slick. Easy to remove, and is tight and stable when mounted.

[mick1955]

hotlicks2go - Thanks, will try to find one at Best Buy, or Circuit City...

[eric.davis]

08Fuston - Just wanted to extend a thank you for your suggestion on mounting the DD. If you take a look at my post you'll see I stole your idea and it works out perfect.